Calculation of Crushing Value Test of Aggregate. Crushing strength of aggregate can be found by the following formula, “Aggregate crushing value is determined by taking a percentage of weight crushed aggregate sample passing through 2.36 mm IS Sieve divided by weight of aggregate sample taken for test” Aggregate crushing value formula is given below
1.The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = (B/A) X 100 where A = weight of oven-dried sample B = weight in 'g' of fraction passing through 2.36 mm IS sieve. 6.Video Aggregate Crushing Value Test
Read MoreCalculation of Aggregate Crushing Value The ratio of weight of fines formed to the weight of total sample in each test shall be expressed as a percentage, the result being recorded to the first decimal place. Aggregate crushing value = (W2 x 100) / (W1-W) W2 =Weight of fraction passing through the appropriate sieve W1-W =Weight of surface dry sample
Read MoreThe weight is recorded as W2. Aggregate Crushing Value (ACV) can be determined by using a simple formula: This test is repeated once or twice and the average crushing value of the aggregate is determined. The average crushing value in the different tests is
Read MoreMay 17, 2019 The ‘ aggregate crushing value test ` gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load under standardized conditions, and the strength of the aggregate
Read Morethe aggregate crushing value (ACV) which gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. The method is applicable to aggregates passing a 14.0 mm test sieve and retained on a 10.0 mm test sieve. For other size fractions, there is another recommended method
Read MoreThe apparatus of the aggregate crushing value test as per IS: 2386 (Part IV) – 1963 consists of: 1) A 15cm diameter open ended steel cylinder with plunger and base plate, of the
Read MoreAggregate Crushing Value = W B W A 100 W B W A 100. Where, W A is weight of surface-dry sample. W B is weight of fraction passing the appropriate sieve. Reporting of Results. The mean of the two results shall be reported to the nearest whole number as the ‘aggregate crushing value’ of
Read MoreJul 18, 2021 Jul 18, 2021 Aggregate crushing value test codes. Following are the standard guidelines for the crushing value test on the aggregates: • IS 2386 (Part 4):1963 • BS 812–110:1990. Objective. The objective of this test is to: 1. Determine the aggregate crushing value of coarse aggregate 2. Check the suitability of coarse aggregates to use in different types of road. Apparatus
Read MoreCalculation of Aggregate Crushing Value. The crushing value of aggregates is measured in the ratio between the crushed aggregates, obtained from the IS sieve 2.36mm and the weight of the dried aggregate sample. At least three samples should be tested from the same batch and average value to get accurate results. The crushing value of aggregate = (W2/W1) x 100. Lab Report
Read MoreMar 30, 2020 Procedure of Aggregate Crushing Value Test:-. Sieve the test material through 12.5 mm and 10.0 mm IS sieve. Take test samples of aggregates passing through 12.5 mm IS sieve and retained on 10 mm IS sieve (minimum 3 Kg). Dry theme in an oven for 4 hours at a temperature of 100 C to 110 C and then cool at room temperature
Read MoreAGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) – 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes – 12.5mm, 10mm and 2.36mm Procedure to determine Aggregate Crushing Value i) The aggregates passing through 12.5mm […]
Read MoreMar 28, 2021 Mar 28, 2021 Aggregate crushing test values indicates the strength of aggregate and hence it is very significant. Similarly we can say crushing value is the relative measure of resistance of an aggregate under gradually applied compressive loads. Higher crushing strength means lower crushing value and vice versa. If the aggregate crushing value is less than
Read MoreSep 12, 2015 Crushing Test Fig-1 Crushing Test Setup. One of the model in which pavement material can fail is by crushing under compressive stress. A test is standardized by IS: 2386 part-IV and used to determine the crushing strength of aggregates. The aggregate crushing value provides a relative measure of resistance to crushing under gradually applied
Read MoreJun 05, 2021 Jun 05, 2021 The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggregate of ‘aggregate crushing value’ 30 or higher, the result may be anomalous, and in such cases the ‘ten percent fines value’ should be determined instead
Read More